Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateCraftsman Torsion Spring Replacement: The Mesquite Owner’s Guide
We replace Craftsman torsion springs with properly matched parts, and in Mesquite the installed price typically runs $180 – $340 for a standard single-spring swap, with same-day availability on most calls. The torsion spring is the coiled steel bar above your door that carries its weight; when it fails, the door suddenly becomes too heavy for the opener to lift. Most Mesquite owners discover the problem the same way: they press the remote, hear the motor strain for a second, and watch the door stop dead or hang crooked. Sometimes there’s a sharp bang from the garage first. If the door rises a few inches and quits, the spring is the first thing we check.
Which Craftsman Models This Applies To
Craftsman branded garage doors and their spring hardware show up across a wide span of installs, from older chain-drive opener packages sold through Sears to newer doors carrying the Craftsman name on the label. The spring itself isn’t usually stamped with a model number, which is the first gotcha. What matters is the spring’s wire gauge, inside diameter, and length – the three measurements that determine lift capacity. A Craftsman door rated for a certain weight needs a spring matched to that weight, and a part pulled off the shelf by guesswork will either run the door too heavy or wind it too tight.
To identify the right part, we look at the door’s weight rating label (often inside the jamb or on the bottom section), measure the existing spring’s coil count and diameter, and confirm the drum and cable setup. That’s where we make the OEM-versus-aftermarket call. Genuine Craftsman replacement springs exist for many models, but a quality aftermarket spring in the correct spec often outlasts the original, and we’ll tell you which route fits your door rather than defaulting to one. Fernbrook Garage Door Repair Mesquite is an independent service provider and isn’t affiliated with Craftsman; we simply know the hardware. We also service LiftMaster, Chamberlain, and Genie systems on the same visit when the opener needs attention.
Styles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
Signs Your Craftsman Torsion Spring Replacement Is Failing
A torsion spring rarely fails without warning. Here’s what Mesquite owners usually notice before it lets go:
- The door feels impossibly heavy when you lift it by hand. A working spring counterbalances most of the door’s weight, so if you’re straining, the spring has lost tension or cracked.
- A loud bang from the garage, often in the morning or evening. That’s the sound of a fatigued spring snapping. In Mesquite’s dry desert heat, springs cycle through big temperature swings, and that repeated expansion and contraction shortens their life compared to milder climates.
- The door opens a few inches and stops, or hangs crooked. With one spring broken on a two-spring door, the remaining spring lifts unevenly and the opener stalls.
- A visible gap in the coil. Look at the spring above the door with the door closed – a clean break or a stretched, separated section means replacement, not adjustment.
- The opener strains or the door slams down. A weak spring forces the opener to fight gravity, which stresses the motor and makes the door drop hard at the bottom.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Torsion spring replacement in Mesquite lands in the $180 – $340 range, and that’s a written price we hand you before any work begins. What moves you up or down the range: whether it’s a single or double spring setup, the spring’s wire gauge and cycle rating, and whether the cables, drums, or bearings need attention at the same time. Cable repair, if needed, runs $130 – $250 on its own.
Here’s what the price covers, stated plainly: the matched spring, the labor to wind and balance it safely, a full door balance check, and lubrication. Every job is backed by our 365-Day Done Right Promise – if it isn’t done right, we make it right. We wear shoe covers and lay drop cloths inside your home, use quiet tools if the kids are napping, and send you a photo of the clean-up before we leave.
DIY or Call Us?
Torsion springs are genuinely dangerous, and we want to be direct about that. The spring holds enough stored energy to cause serious injury, and the winding process requires the right bars and a controlled technique. Please don’t try to wind, unwind, or remove a torsion spring yourself.
What you can safely do: check the spring visually with the door closed (look for a gap or break), test the door’s weight by hand with the opener disconnected, and note whether the door hangs crooked. That’s useful information to share when you call. Beyond that, this is a job for a trained technician. Our technicians have up to 24 years of experience with Craftsman hardware, and a live person answers the phone 24 hours a day. Call (888) 255-7680 – estimates are free, and we’ll confirm the price before we start.
FAQs
How long does a Craftsman torsion spring last?
A standard spring lasts roughly 10,000 to 15,000 open-close cycles, which works out to several years of typical daily use. In Mesquite’s dry, hot climate, the wide temperature swings we get here can shorten that lifespan, so our springs are rated for the conditions and we tell you the cycle rating up front. Call (888) 255-7680 for a free estimate.
Can you repair the spring instead of replacing it?
No – a cracked or broken torsion spring can’t be repaired, only replaced. Springs are single-piece wound steel, and once the coil fails there’s nothing to rewind or patch. Sometimes we can replace just the failed spring on a two-spring door, but on most setups we recommend replacing both together so they stay balanced. Call (888) 255-7680 and we’ll walk you through the options.
How long does the swap take?
A standard torsion spring replacement takes about an hour for a single-spring door, and a bit longer for a double setup or when cables and drums are addressed too. We schedule same-day on most Mesquite calls. Call (888) 255-7680 to book a time that fits your day.
How do you source the part?
We match your Craftsman door’s specific spring spec – wire gauge, inside diameter, and length – and source either a genuine replacement or a quality aftermarket spring rated for your door’s weight and cycle count. The price for the matched part is in the written estimate, and it’s confirmed before we start. Call (888) 255-7680 for a free estimate.
Call (888) 255-7680 for a free estimate on Craftsman torsion spring replacement in Mesquite. We answer live around the clock, give you a written price before any work, and back every job with the 365-Day Done Right Promise.
Written by the team at Fernbrook Garage Door Repair Mesquite, serving Mesquite and nearby areas.